Firmware update for WLC Wi-Fi controllers. Version 1.30.6

Wi-Fi

11 November 2025

Firmware update

Firmware version: 1.30.6

The firmware and detailed description of the product capabilities are available in the Downloads or on the product page.

Key changes in 1.30.6

Support for portal authorization with Eltex-NAICE
Security:
- Ability to view the WIDS event log in the WEB interface, as well as send SNMP traps for events
Reliability:
- Synchronization of WLC logs during redundancy
Convenience:
- Configuration of RADIUS server and VLAN via the WEB interface
- Ability to redirect AAA RADIUS requests for different SSID to different servers

Added

Monitoring:
- Ability to filter WEB server syslog messages
- snmp-server enable traps wlc-wids command to enable sending SNMP traps for WIDS events
WEB:
- WIDS log
- Displaying the hostname on AP monitoring pages
- Displaying the utilization and interference parameters in AP radio interface monitoring
- RADIUS server settings section
- VLAN settings section
- Disconnect-on-reject setting in the portal profile
- ARP suppression configuration in the radio profile (not supported for WEP/WOP-2ac, WEP-3ax, WEP-550K)
- Date format in filters in the “Event Log” section has been changed
- Sorting of configuration files by date has been improved
- UI interface has been improved
WLC:
- Support for portal authorization with Eltex-NAICE for WEP-30L/WEP-30L-NB/30L-Z and WOP-30L/30LI/30LS
- Support for WEP-550K, WEP-30L-NB, WOP-3L-EX
- Support for redirecting CoA requests to radius-server local for portal authorization
- Synchronization of WLC logs during redundancy
- Displaying the utilization and interference parameters in extended AP monitoring
- Unified format for displaying AP firmware in the show wlc ap firmware command
- show wlc journal info command for viewing summary information about WLC logs
- Units of measurement for speed in the show wlc ap interfaces <mac> output
- disconnect-on-reject command in portal-profile to disconnect the user upon Reject from RADIUS during MAB authentication (supported for WEP-30L/WEP-30L-NB/30L-Z and WOP-30L/30LI/30LS)
- http-auth-disable command in portal-profile to disable portal interaction with the AP via HTTP/HTTPS during user authorization
- neighbor-scan command in ap-profile to configure passive scanning has been extended for WEP-200L, WOP-20L, and WEP-2ax
- captive-adaptive command in ap-profile to enable portal authorization compatibility mode for iOS devices
- redirect-url-format command in portal-profile to specify the format of the user's MAC address and the format of the NAS ID in the redirect address when configuring portal authorization
- description command for user in radius-server local
- Configuring url-acl-profile and ipv4-acl in ap-profile and portal-profile to configure domain and IP address lists on the AP. The lists are used for unauthorized portal users
- Block of commands in ap-profile for configuring DAS parameters on the AP
- Block of commands in radius-server local for configuring DAS parameters used when redirecting CoA requests
- Ability to add a location name to redirect-url-custom in portal-profile
- Ability to redirect AAA RADIUS requests for different SSID to different servers
- The default value for the load-balance command in airtune-profile has been changed from “enabled” to “disabled”
SNMP:
- Table containing information about APs indexed by MAC address
- WIDS traps
- OID for viewing radio channel utilization by incoming traffic
- OID for viewing radio channel utilization by outgoing traffic
- OID for viewing the overall interference level
- OID for viewing the interference level from non-Wi-Fi devices
- OID for viewing interference level from Wi-Fi devices operating on the same channel
- OID for viewing noise level on the radio channel
- OID for viewing the percentage of packets damaged due to interference, weak signal, or collisions
- OID for viewing available memory
Licensing:
- Increased license lifetime when ELM is unavailable