New
Wireless access point WEP-200L
Mass production
Key benefits
WEP-200L provides easy and secure access to a high-speed wireless network that combines many of the features and services required by corporate clients. WEP-200L will become a universal solution for organizing a wireless network with a large number of users and high traffic (office, government agencies, conference rooms, laboratories, hotels, etc.).
Scalability
The WEP-200L Wi-Fi access point is an up-to-date flexible solution that allows changing the network coverage area in order to increase the quantity of serviced mobile devices. Due to a high-performance hardware platform, scalability features and intuitive interface, it is possible to deploy wireless IT infrastructure easily and quickly.
Wireless connection
Due to support for IEEE 802.11n/ac standards, the WEP-200L access point provides up to 300 Mbps (2.4 GHz) and up to 1733 Mbps (5 GHz) data rates. The use of MIMO technology and embedded omnidirectional antennas makes WEP-200L a universal solution for corporate networks construction.
Security
WEP-200L uses up-to-date authentication and encryption technologies, that provide personal data protection and environment security of the corporate network. In particular, an individual dynamic key is used for each subscriber device working with WEP-200L.
Performance
To ensure stable and continuous operation of the device, the high-performance processors are used to achieve high data processing rates.
Power supply
The PoE technology makes it possible to install equipment in any place, regardless of the power supply source location. That allows reducing the number of cables used and lowering the total cost. The PoE technology makes installation easier and faster.
- Dual band access point
- Support for 802.11ac
- Radio interface 2.4 GHz with MIMO 2×2 support
- Radio interface 5 GHz with MIMO 4×4 support
- PoE power supply (IEEE 802.3af-2003)
- Up-to-date authentication and encryption means
WEP-200L provides easy and secure access to a high-speed wireless network that combines many of the features and services required by corporate clients. WEP-200L will become a universal solution for organizing a wireless network with a large number of users and high traffic (office, government agencies, conference rooms, laboratories, hotels, etc.).
Scalability
The WEP-200L Wi-Fi access point is an up-to-date flexible solution that allows changing the network coverage area in order to increase the quantity of serviced mobile devices. Due to a high-performance hardware platform, scalability features and intuitive interface, it is possible to deploy wireless IT infrastructure easily and quickly.
Wireless connection
Due to support for IEEE 802.11n/ac standards, the WEP-200L access point provides up to 300 Mbps (2.4 GHz) and up to 1733 Mbps (5 GHz) data rates. The use of MIMO technology and embedded omnidirectional antennas makes WEP-200L a universal solution for corporate networks construction.
Security
WEP-200L uses up-to-date authentication and encryption technologies, that provide personal data protection and environment security of the corporate network. In particular, an individual dynamic key is used for each subscriber device working with WEP-200L.
Performance
To ensure stable and continuous operation of the device, the high-performance processors are used to achieve high data processing rates.
Power supply
The PoE technology makes it possible to install equipment in any place, regardless of the power supply source location. That allows reducing the number of cables used and lowering the total cost. The PoE technology makes installation easier and faster.
Show all
Specifications
Documents and files
Warranty
Interfaces
Security
Receiver sensitivity
Physical specifications
1 The number of channels and the value of the maximum output power will vary according to the rules of radio frequency regulation in your country.
2The maximum wireless data rate is defined according to IEEE 802.11 standards. The real bandwidth can be different. Conditions of the network, environment , the amount of traffic, building materials and constructions and network service data can decrease the real bandwidth. The environment can influence the network coverage range.
- 1 port of 10/100/1000BASE-T (RJ-45) with PoE support
- Wi-Fi 2.4 GHz IEEE 802.11b/g/n
- Wi-Fi 5 GHz IEEE 802.11a/n/ac
- Support for IEEE 802.11a/b/g/n/ac
- 802.11r/k/v roaming
- Data aggregation, including A-MPDU (Tx/Rx) and А-MSDU (Rx)
- WMM-based packet priorities and planning
- Dynamic frequency selection (DFS)
- Support for hidden SSID
- 14 virtual access points
- Detection of access points from other vendors
- Spectrum analyzer
- WDS support
- APSD
- Automatic speed negotiation, duplex mode negotiation and MDI–MDI-X switch-over
- VLAN support (Access, Trunk, General)
- DHCP client
- GRE
- Transmission of subscriber traffic outside of tunnels
- ACL
- NTP
- Syslog
- IPv6
- Packet priorities and planning based on profiles
- Bandwidth limiting for each SSID
- Remote management via Telnet, SSH
- CLI
- NETCONF
- Web interface
- SNMP
Regulatory Compliance
CE marked:
- EN IEC 62311:2020
- EN IEC 62368-1:2020+A11:2020
- EN 301 489-1 V2.2.3
- EN 301 489-3 V2.1.1
- EN 301 489-17 V3.2.4
- EN 55032:2015+A1:2020
- EN 55035:2017+A11:2020
- EN IEC 61000-3-2:2019+A1:2021
- EN 61000-3-3:2013+A2:2021
- EN 300 328 V2.2.2
- EN 301 893 V2.1.1
- EN 300 440 V2.2.1
Security
- Centralized autorization via RADIUS server (802.1X WPA/WPA2 Enterprise)
- WPA/WPA2 encryption
- Captive Portal
- Autorization via RADIUS server when logging into the device
- Frequency range 2400–2483.5 MHz; 5150–5350 MHz; 5470–5850 MHz
- BPSK, QPSK, 16QAM, 64QAM, 256QAM modulations
-
Support for:
- MIMO 2×2 for 2.4 GHz
- MIMO 4×4 for 5 GHz
-
Bandwidth:
- 20, 40 MHz for 2.4 GHz;
- 20, 40 and 80 MHz for 5 GHz
- 802.11b/g/n: 1–13 (2402–2482 MHz)
-
802.11a/n/ac:
- 36–64 (5170–5330 MHz)
- 100–144 (5490–5730 MHz)
- 149–165 (5735–5835 MHz)
- 802.11a: up to 54 Mbps
- 802.11b: up to 11 Mbps
- 802.11g: up to 54 Mbps
-
802.11n:
- 2.4 GHz — up to 300 Mbps
- 5 GHz — up to 600 Mbps
- 802.11ac: up to 1733 Mbps
- 2.4 GHz: 18 dBm
- 5 GHz: 20 dBm
Built-in antenna gain
- 2.4 GHz: ~3 dBi
- 5 GHz: ~3 dBi
- 2.4 GHz: up to -92 dBm
- 5 GHz: up to -92 dBm
Physical specifications
- Power consumption: no more than 12.95 W
- 128 MB SPI-NAND Flash
- 256 MB RAM DDR3 RAM
- Power supply: PoE 48 V/56 V (IEEE 802.3af-2003)
- Operating temperature: from +5 to +40 °С
- Dimensions (Diameter × Height): 230 × 56 mm
- Weight: 0.46 kg
1 The number of channels and the value of the maximum output power will vary according to the rules of radio frequency regulation in your country.
2The maximum wireless data rate is defined according to IEEE 802.11 standards. The real bandwidth can be different. Conditions of the network, environment , the amount of traffic, building materials and constructions and network service data can decrease the real bandwidth. The environment can influence the network coverage range.
Show all
Descriptions
Documentations
Certificates
Operational lifetime of the ELTEX equipment
In development
1
Pre-production
2
Mass production
3
Mass production is over
4
Sold out
5
Support is over
6
During the warranty period the manufacturer ensures technical support and free-of-charge repair at the Enterprise which is situated in Novosibirsk.
As part of the warranty service, technical support is provided on the first-in first-out principle.
The priority support packages of 8/5 and 27/7 types are subjects to additional charges.
News
