MPLS router ME5100

Mass production

MЕ Series routers are multifunctional devices with a high port density intended for use in provider networks as aggregation router and IP/MPLS network transport border routers. These routers are cost-effective, compact and high-performance solution which can be used to organize operator’s points of presence when providing data services for large customers with high reliability requirements. Fault tolerance of devices is ensured by redundant power supplies (1+1) and by replaceable fan modules. All redundant units are hot-swappable.

In addition to traffic routing and switching, the main functionality of the device includes wide support for MPLS switching mechanisms, such as MPLS Layer3 VPN, VPLS (Kompella/Martini), VPWS with pseudowire backup capabilities, Multicast routing with support for PIM-SM/PIM- SSM/MSDP/Anycast PIM, as well as rich QoS capabilities. This set of functions allows to use devices as full-featured provider edge (PE) routers.

ME5100 and ME5200 are routers with a fixed set of network interfaces, hot-swappable power supplies and fan modules and can be used in those networks points where high performance in a compact form factor is required. Routers are designed for installation in 19" constructive and have a height of 2U.

Show all

Integrated interfases

20 network interfaces of 10GE SFP+. Support 1GE mode (1000BASE-X).
Available usage of 1000BASE-T SFP transceivers.
Out Of Band (OOB) 1GE port (10/100/1000BASE-T)
RS-232 console port (RJ-45)
1 x USB 2.0
Synce synchronization clock input and output (SMB, 50Ohm)

Performance

Throughput and SyStem performance - 200 Gbps, 300 Mpps
Buffer memory - 6GB
RAM - 8GB
MAC table - 250K
Bridge domains - up to 4K
Routing table:
- FIB: up to 1M IPv4 or up to 512K IPv6. Resource shared with MPLS switching tables and elements of single-hop BFD sessions. RIB is limited by free RAM capacity
L3 interfaces - up to 4K
MPLS PW - up to 12K
ARP table - up to 20K
VRF (MPLS L3VPN) - up to 1000 (up to 128 with BGP process instances launched in every VRF)
QoS queues - 96k

Physical parameters

Air flow:

Front-to-back air flow
Three hot-swappable fan modules

Power sources - Two hot-swappable power modules
- AC: 150..250V 50Hz
- DC: 36..72V
Maximum power consumption - 250 W
Operating temperature - from 0 to 45^oC
Weight - 9.5 kg
Dimensions (WхHхD) - 440 х 87 х 500 mm

Interfaces functions

Link aggregation groups: static LAG and LACP
Equal load balancing in group
Multi-chassis LAG
BFD (Bidirectional Frowarding Detection) over LAG, single connec- tion failure detection (RFC 7130)
Traffic mirroring - SPAN, RSPAN

L2 functions

Providing Ethernet switching through the bridge domains and cross-connects
IEEE bridging (IEEE 802.1d)
VLAN (IEEE 802.1q)
Q-in-Q (IEEE 802.1ad) with push/pop/swap/replace tag operations
SpanningTree protocols (STP, RSTP, MSTP)
LLDP

L3 protocols and functions

Static IPv4, IPv6 Unicast Routing
IS-IS
OSPFv2, OSPFv3
Border Gateway Protocol (BGP)
BGP Route Reflector, BDP Additional Path
Route filtering (routemap, prefix-list)
BFD protocol for routing protocols and static routes
IP FastReroute/Loop Free Alternate for OSPF/IS-IS
VRRP (version 2), DHCP relay agent
IPv4 ACL (access control lists) for transit traffic
ECMP load balancing

Multicast management

PIM-SM, PIM-SSM, Anycast RP
IGMP v2/v3, SSM mapping
MSDP
IPv6 MLDv1, v2
MPLS FUNCTIONS
Multiprotocol extensions for BGP-4
Label Distribution Protocol (LDP)
MPLS pseudowire with PW backup functionality

L2VPN
VPWS
VPLS LDP signalling (draft-martini)
VPLS BGP signalling (draft-kompella)

L3VPN
- L3VPN for AFI/SAFI vpnv4 unicast and vpnv6 unicast
- L3VPN inter-AS option A

Quality of Service (QoS)

Ingress policing, ingress/egress shaping
SP and DeficitWRR queuing algorithms
Rate limiting, Storm Control
Up to 8 queues per logical interface, up to 32K queues per physical interface

Reliability functions

Graceful Restart for routing protocols
Non-stop forwarding
Active and backup firmware images
Ability to restore the previous firmware version during update

Management and monitoring

Command Line Interface (CLI), SSH, Telnet for remote manage- ment
SNMPv1, v2c for monitoring the device status
NETCONF protocol
Statistic data export (Netflow V9)
Configuration backup and restore (local, FTP, SFTP, TFTP)
RADIUS, TACACS+ authentication and authorization, accounting via TACACS+
Remote software retrofit
System parameters and resources monitoring
Syslog
Time synchronization, NTP, SNTP
Control-plane protection and rate-limiting

Show all

1 fiber	Part Number
SFP 1.25 GE module, 3 km, SM, 1 fiber, TX/RX 1310/1550 SC set, DDM	FH-SB3512CDS3 / FH-SB5312CDS3
SFP 1.25 GE module, 3 km, SM, 1 fiber, TX/RX 1310/1550 LC set, DDM	FH-SB3512CDL3 / FH-SB5312CDL3
SFP 1.25 GE module, 20 km, SM, 1 fiber, TX/RX 1310/1550 SC set, DDM	FH-SB3512CDS20 / FH-SB5312CDS20
SFP 1.25 GE module, 20 km, SM, 1 fiber, TX/RX 1310/1550 LC set, DDM	FH-SB3512CDL20 / FH-SB5312CDL20
SFP 1.25 GE module, 20 km, SM, 1 fiber, TX/RX 1310/1550 SC set, DDM, INDUSTRIAL	FH-SB3512IDS20 / FH-SB5312IDS20
SFP 1.25 GE module 40 km, SM, 1 fiber, TX/RX 1310/1550 LC set, DDM	FH-SB3512CDL40 / FH-SB5312CDL40
SFP 1.25 GE module 40 km, SM, 1 fiber, TX/RX 1310/1550 SC set, DDM	FH-SB3512CDS40 / FH-SB5312CDS40
SFP 1.25 GE module 80 km, SM, 1 fiber, TX/RX 1490/1550 LC set, DDM	FH-SB4512CDL80 / FH-SB5412CDL80
SFP 1.25 GE module 80 km, SM, 1 fiber, TX/RX 1490/1550 SC set, DDM	FH-SB4512CDS80 / FH-SB5412CDS80
SFP 1.25 GE module 120 km, SM, 1 fiber, TX/RX 1490/1550 LC set, DDM	FH-SB4512CDL120 / FH-SB5412CDL120
SFP 1.25 GE module 120 km, SM, 1 fiber, TX/RX 1490/1550 SC set, DDM	FH-SB4512CDS120 / FH-SB5412CDS120
SFP 1.25 GE module 160 km, SM, 1 fiber, TX/RX 1490/1550 LC set, DDM	FH-SB4512CDL160 / FH-SB5412CDL160
2 fibers
SFP 1.25 GE module 550 m, MM, 2 fibers, 850 nm, LC, DDM	FH-S8512CDL05
SFP 1.25 GE module 2 km, ММ, 2 fibers, 1310 nm, LC, DDM	FH-S3112CDL2
SFP 1.25 GE module 20 km, SМ, 2 fibers, 1310 nm, LC, DDM	FH-S3112CDL20
SFP 1.25 GE module 40 km, SМ, 2 fibers, 1310 nm, LC, DDM	FH-S3112CDL40
SFP 1.25 GE module 80 km, SМ, 2 fibers, 1550 nm, LC, DDM	FH-S5512CDL80
SFP 1.25 GE module 120 km, SМ, 2 fibers, 1550 nm, LC, DDM	FH-S5512CDL120
SFP 1.25 GE module 160 km, SМ, 2 fibers, 1550 nm, LC, DDM	FH-S5512CDL160
SFP+
1 fiber
SFP+ 10GE module 3 km, SM, 1 fiber, TX/RX 1290/1310 LC set, DDM	FH-SPB311TCDL3 / FH-SPB191TCDL3
SFP+ 10GE module 20 km, SM, 1 fiber, TX/RX 1330/1270 LC set, DDM	FH-SPB231TCDL20 / FH-SPB321TCDL20
SFP+ 10GE module 40 km, SM, 1 fiber, TX/RX 1330/1270 LC set, DDM	FH-SPB231TCDL40 / FH-SPB321TCDL40
SFP+ 10GE module 60 km, SM, 1 fiber, TX/RX 1330/1270 LC set, DDM	FH-SPB231TCDL60 / FH-SPB321TCDL60
SFP+ 10GE module 80 km, SM, 1 fiber, TX/RX 1490/1550 LC set, DDM	FH-SPB451TCDL80 / FH-SPB541TCDL80
SFP+ 10GE module 100 km, SM, 1 fiber, TX/RX 1490/1550 LC set, DDM	FH-SPB451TCDL100 / FH-SPB541TCDL100
2 fibers
SFP+ 10GE module, 0.3 km, MM, 2 fibers, 850 nm, LC, DDM	FH-SP851TCDL03
SFP+ 10GE module, 20 km, SM, 2 fibers, 1310 nm, LC, DDM	FH-SP311TCDL20
SFP+ 10GE module, 40 km, SM, 2 fibers, 1550 nm, LC, DDM	FH-SP551TCDL40
SFP+ 10GE module, 80 km, SM, 2 fibers, 1550 nm, LC, DDM	FH-SP551TCDL80
SFP+ 10GE module, 100 km, SM, 2 fibers, 1550 nm, LC, DDM	FH-SP551TCDL100
SFP/SFP+ transceivers with RJ-45 interface
SFP transceiver of 10/100/1000 BASE-T	FH-ST2
SFP+ transceiver of 10GBASE-Т	FH-10SFP-T
SFP+ Direct Attach Cable
SFP+ Direct attach cable, 10G, 1m	FH-DP1T30SS01
SFP+ Direct attach cable, 10G, 2m	FH-DP1T30SS02
SFP+ Direct attach cable, 10G, 3m	FH-DP1T30SS03
SFP+ Direct attach cable, 10G, 5m	FH-DP1T30SS05

Descriptions

Datasheet

Downloads

Operational lifetime of the ELTEX equipment

Regardless of the operational lifetime stage, Eltex provides a 12 months warranty on all its telecommunication equipment.
During the warranty period the manufacturer ensures technical support and free-of-charge repair at the Enterprise which is situated in Novosibirsk.
As part of the warranty service, technical support is provided on the first-in first-out principle.
The priority support packages of 8/5 and 27/7 types are subjects to additional charges.